Difference between revisions of "Gen3 INSTALL"
(Created page with '.') |
|||
| Line 1: | Line 1: | ||
| − | . | + | Welcome to WDLXTV! Be aware that the software offered here is unofficial and could damage your device (but probably won't :). Proceed at your own risk; you have been warned! |
| + | |||
| + | |||
| + | == Download the Firmware == | ||
| + | |||
| + | |||
| + | Download the latest firmware for your device. Ensure you get firmware appropriate to your device model (Gen3). | ||
| + | |||
| + | == Install == | ||
| + | |||
| + | Gen3 Firmware does not get Flashed to the device. Gen3 firmware will always run live off a USB drive. | ||
| + | |||
| + | |||
| + | This process will require that your WD Gen3 be reachable over your LAN network. | ||
| + | |||
| + | |||
| + | '''Windows Instructions''' | ||
| + | |||
| + | 1. Download package as noted above | ||
| + | |||
| + | 2. Unzip | ||
| + | |||
| + | 3. Edit device-ip.txt (included in download) | ||
| + | |||
| + | 4. run win-homebrew-upload.bat | ||
| + | |||
| + | 5. run win-homebrew-brewme.bat | ||
| + | |||
| + | 6. run win-homebrew-status.bat - If this does not say "Homebrew Mode: ON" , then it did not work | ||
| + | |||
| + | 7. place 2.02.32-WDLXTV_Gen3-0.1.5.bin on thumbdrive | ||
| + | |||
| + | 8. place homebrew files on same thumbdrive (2.02.32-WDLXTV_Gen3-0.1.5.bin, runsit.sh, wdtvlivegen3.bin.mpm, wdtvlivegen3.bin.mpm.sha1.sum) | ||
| + | |||
| + | 9. plug thumbdrive into Gen3 | ||
| + | |||
| + | 10. Reboot Gen3 | ||
| + | |||
| + | 11. Confirm settings - system - about shows the firmware version as "2.02.32-WDLXTV_Gen3-0.1.5" - or something similiarly tagged | ||
| + | |||
| + | 12. Thumbdrive must stay plugged in, as firmware is running live on the thumbdrive | ||
| + | |||
| + | |||
| + | |||
| + | == TroubleShooting == | ||
| + | |||
| + | 1. NTFS drives do '''NOT''' work - FAT32 is recommended | ||
| + | |||
| + | 2. EXT3 format drive - make sure runsit.sh has executable permissions | ||
| + | |||
| + | 3. If all else fails reset the device using WEC, or via command line | ||
Revision as of 15:31, 15 December 2014
Welcome to WDLXTV! Be aware that the software offered here is unofficial and could damage your device (but probably won't :). Proceed at your own risk; you have been warned!
Download the Firmware
Download the latest firmware for your device. Ensure you get firmware appropriate to your device model (Gen3).
Install
Gen3 Firmware does not get Flashed to the device. Gen3 firmware will always run live off a USB drive.
This process will require that your WD Gen3 be reachable over your LAN network.
Windows Instructions
1. Download package as noted above
2. Unzip
3. Edit device-ip.txt (included in download)
4. run win-homebrew-upload.bat
5. run win-homebrew-brewme.bat
6. run win-homebrew-status.bat - If this does not say "Homebrew Mode: ON" , then it did not work
7. place 2.02.32-WDLXTV_Gen3-0.1.5.bin on thumbdrive
8. place homebrew files on same thumbdrive (2.02.32-WDLXTV_Gen3-0.1.5.bin, runsit.sh, wdtvlivegen3.bin.mpm, wdtvlivegen3.bin.mpm.sha1.sum)
9. plug thumbdrive into Gen3
10. Reboot Gen3
11. Confirm settings - system - about shows the firmware version as "2.02.32-WDLXTV_Gen3-0.1.5" - or something similiarly tagged
12. Thumbdrive must stay plugged in, as firmware is running live on the thumbdrive
TroubleShooting
1. NTFS drives do NOT work - FAT32 is recommended
2. EXT3 format drive - make sure runsit.sh has executable permissions
3. If all else fails reset the device using WEC, or via command line
